Mumbai

Item Tag: Motherboard

Nintendo DS Lite USB-C Replacement charge port w/ Jig+Bezel -USBC diy kit V2

UPDATED: It’s now a slip on resin jigThis is a PCB USB-C charging port to replace the original charging port on the Nintendo DSL, this port works with USB-C to USB-C cable charging so you don’t need to worry about having a USB to USB-C cable. The Installation jig allows you to solder down the board while holding it in alignment, two thumb screws are provided for easy assembly and disassembly of the jig. Due to the heat of the iron I consider the jig to be a single use item but I’ve started printing them out of ASA for greater thermal resistance. Here is my installation process: BOARD INSTALLATION1. Disassemble your Nintendo DS Lite, be very mindful of the trigger springs and rods 2. Remove the PCB. 3. Use a hot air station @290C (no more than 30-40 seconds is necessary) to remove the original charging port (preheat the board with a hot plate @168C or use the hot air station to preheat the board) 4 Optional. Clean the PCB pads, and use sand paper or a rotary too to expose the top most trace (it’s the one nearest to the edge). Add solder to this exposed trace, it will melt into the USB-C receptacle making a stronger hold 5. Place the USBC board into the resin jig (if not already in there) and then firmly slip the jig onto the PCB there is a silk screen square around the component next to the fuse (the component circled in red in the pictures) try to line up the edge of the USBC board with that to give you a good idea if it’s on straight. 6. Turn the PCB board over and apply flux to the holes. 7. Use a decent amount of solder to the affix the board. I have my iron at 295C for this and I rotate between all of the pads/holes to make sure a decent of amount of solder flows through. 8. Use a multimeter to test GND (-) and VCC(+) make sure that they’re not shorted and that you have good connections between PCB GND and USBC board GND and the same for VCC. 9. After continuity testing you’ll need to snip the curled arm on the resin jig so that you can properly remove the resin jig (I use flush cutters). SANDING/FITTING1. Set aside any loose plastic parts from the bottom half of your DS lite so you don’t lose them. 2. The USB-C receptacle hangs over the motherboard (expected) however the tips of the USB-C board hang over the motherboard as well and they cause interference with the bottom half of the DS lite. I use flush cutters to nip off the majority of it. Now you have a decision to make either grind it away with a rotary tool or file so it’s flush with the motherboard (the board not the receptacle) or do the filing on the bottom half of the DS lite (I HIGHLY recommend you do the latter the amount of filing of the USBC board is obscene and there will be metal dust everywhere). The filing on the bottom half of the DS lite would need to be done on the inner side of the wall directly on the left and right of the charging port cutout (essentially thinning that section of the wall). 3. Look at the screwhole/post to the immediate left of the charging port section of the bottom half of the ds lite, you will need to cut the raised portion. The depth of your cut should be to the flat part of the screw hole and it should encompass half of the circular flange (look at the photos to see it). 4. You will need to cut down the raised walls that secure the old charging port in the bottom half of the DS lite, the walls will have to be cut down to the height of the charging port cutout (refer to the photo in the listing but you don’t need to totally remove the right wall like I did. 5. Now we’ll check for the clearance of the USB-C receptacle, take the motherboard and place it in the bottom half of the DS lite and see if the USB-C receptacle slides into the charging port cutout, if it’s too snug lightly file the sides of the cutout. 6. Take the bezel and fit it into the three hole section of the charging port section of the bottom half of the DS lite it should fit easily and then place the motherboard in the bottom half of the DS lite to check for fit. Sand and file down any obstructions until you have a good fit. The sanding is the hardest part. REQUIRED BUT NOT INCLUDED TOOLS: 1. A soldering Iron2. Flux3. Solder4. Screwdrivers5. Multimeter6. Grinding pen or rotary tool or files (highly) RECOMMENDED BUT NOT INCLUDED TOOLS: 1. Hot air station2. Hot plate INCLUDED: 1. USB-C PCB board fully assembled2. 3D Printed Installation Jig3. Two 3D Printed bezels

OEM Tested Nintendo DS Lite Working Motherboard With Wifi Card

Motherboard is completely functional and comes with the wifi card. The button contacts may be cleaned and sanded if needed and the trigger buttons may be cleaned if needed. In response to multiple reports, any warranty is based on the condition of the board upon being received. I will send a refund if the board is damaged upon delivery, but I cannot send a refund if it is believed that damage is done through user error.

Sony PS5 PlayStation 5 Motherboard Service | Motherboard Repair

PS5 Motherboard Repair Mail-in Repair Service (Board Only)(FAST REPAIR 1-2 DAY TURN AROUND TIME) 1 YEAR GUARANTEE with FREE return shipping. If you want to send it the whole console please see my other listing.We have over 10 years experience fixing gaming consoles and are highly rated on eBay and locally. We can fix any issues with your PS5 Motherboard. Check out our feedback! Our mail-in repair service ensures that we can fix any issues with ease, so you can get back to gaming right away. **We are the #1 trusted repair service on eBay with over 600 gaming consoles repaired successfully. We have been made aware of other sellers using our photos and/or descriptions to sell similar repair services. They are in no way affiliated with us. Please be mindful of who you are purchasing from** Did another repair shop tell you your PS5 can’t be fixed? Send it in to us we will fix it! Our Technicians have many years experience in motherboard repairs. We can repair PS5 consoles that others can’t! Don’t be fooled by low prices on eBay to draw you in to send the unit, then charge you more for non existing problem. **EXTRA BONUS OFFER** Have a controller that has stick drift? We can repair it at a discounted price found no where else. Just include it inside the package. 1. NOT EVERY UNIT CAN BE REPAIRED BUT 99% ARE REPAIRABLE EVEN IF PRIOR REPAIR ATTEMPTS WERE MADE. 2. IF WE CANNOT FIX YOUR UNIT INITIALLY YOU WILL BE REFUNDED MINUS ACTUAL RETURN SHIPPING CHARGES AND $20.00 DIAG FEE. WE OFFER THESE SERVICES AS AN OPPORTUNITY FOR YOU TO SAVE MONEY ON EXPENSIVE ALTERNATIVES LIKE REPLACEMENT. THIS PRICE IS ONLY THE BENCH FEE THAT BE APPLIED TO THE REPAIR COST SEND JUST THE PS5 CONSOLE NOTHING ELSE UNLESS WE ASK FOR IT. $30 BENCH FEE WILL BE APPLIED TO THE TOTAL REPAIR DEPENDING ON THE PROBLEM. SEE PRICES BELOW! INSTRUCTIONS: 1) PURCHASE THIS LISTING.2) YOU WILL RECEIVE DETAILS TO SHIP YOUR BOARD.3) WE WILL TEST YOUR BOARD AND PROVIDE YOU A TOTAL REPAIR COST ($30 WILL BE APPLIED TO TOTAL REPAIR COST)4) ONCE THE REPAIR IS COMPLETED WE WILL SHIP OUT THE BOARD WITH TRACKING #. (FREE STANDARD RETURN SHIPPING INCLUDED IN THE USA)5) 10 DAY HANDLING TIME TO COVER SHIPPING TO US THEN REPAIR TIME AND SHIPPING BACK TO YOU. REPAIRS ARE DONE WITHIN 2 BUSINESS DAYS. EXPEDITED SHIPPING AVAILABLE PLEASE CONTACT US. PRICES: HDMI PORT: $60POWER ISSUES: $100-$180BAD BIOS CHIP (3 BEEPS) $100ETHERNET PORT: $100USB PORTS: $60BROKEN FAN CONNECTOR: $80ENCODER CHIP: $140DISC DRIVE CONNECTOR REPAIR: $80DISC DRIVE NOT WORKING $100BROKEN HDMI PORT PADS: $100IF YOU DONT SEE YOUR ISSUE LISTED PLEASE CONTACT US Total repair cost will be minus the $30 already paid for this listing!EXAMPLE: Total cost repair $100 minus $30 you will owe $70 once repair is completed. (DO YOU HAVE A REPAIR SHOP? WE WORK WITH HUNDREDS OF REPAIR SHOPS AROUND THE USA, CONTACT US TO SETUP AN ACCOUNT. WE WOULD LOVE TO WORK WITH YOU) PROBLEM SOLUTION THE FOLLOWING ARE THE ISSUES THIS SERVICE COVERS:LIQUID SPILL DAMAGEPORT ISSUESCHARGING ISSUESPOWER UP ISSUESLOSE PORTOVERHEATINGNO POWER’MUCH MORE EXECUTE REPAIRS AND WARRANTY OUR WORK. ALSO WE WILL:SONIC WASH YOUR BOARD FOR LIQUID SPILLSCLEAN INTERNALS FROM DUST & LINTREPAIR YOUR UNIT WITHIN 1-2 BUSINESS DAYS (UNLESS ADDITIONAL PARTS ARE NEEDED) SOME LIQUID SPILL UNITS MAY TAKE LONGERREFUND YOUR MONEY IF THE UNIT CANNOT BE REPAIRED MINUS ACTUAL RETURN SHIPPING COSTS TO YOU AND $10 BENCH FEE. ANY QUESTIONS PLEASE FEEL FREE TO ASK WARRANTY: ONCE YOUR UNIT IS REPAIRED WE PROVIDE A LIMITED 1 YEAR WARRANTY AS INDICATED IN THE LISTING DETAILS TO COVER ANY FUTURE ISSUES FOR THE SAME PROBLEM. REFUNDS ARE ONLY ISSUED IF YOUR UNIT CANNOT BE REPAIRED BY US INITIALLY. REFUNDS ARE NOT ISSUED FOR THE WARRANTY PERIOD OR WARRANTY CLAIMS EXCEPT AS STATED IN THE REFUND POLICY UNDER THIS AGREEMENT. BUYER IS RESPONSIBLE FOR ALL SHIPPING COSTS FOR WARRANTY CLAIMS. REPAIR TIME:UNLESS OTHERWISE INDICATED IN THE LISTING MOST UNITS CAN BE REPAIRED IN 1-2 BUSINESS DAYS. BUSINESS DAYS DO NOT INCLUDE SATURDAY, SUNDAY OR HOLIDAYS IN WHICH THE US POSTAL SERVICE IS CLOSED. ALSO A BUSINESS DAY DOES NOT INCLUDE THE DAY YOUR UNIT ARRIVES AT OUR LOCATION AS IT USUALLY ARRIVES AT THE END OF THE DAY. REPAIR TIMES DO NOT INCLUDE SHIPPING TIME AS THAT MAY VARY ON THE SERVICES YOU CHOOSE TO PURCHASE. SOME REPAIRS MAY TAKE LONGER THAN EXPECTED.

Original Xbox motherboard 1.0 w/HDD – Warranty Included

Motherboard version : 1.0. This motherboard/Hard-drive combo will only work in 1.0-1.4 cases (due to ground points) with 1.0/1.1 power supplies. Replaced Thermal Pad/Paste : Yes. Cleaned: Yes. Ethernet Port Tested: Tested, Functional.